• Guide: How To Use The SMPL Mech Mod

    Welcome to the vapor puffs guide on how to use the SMPL Mech Mod. In this guide, we’ll start off by looking at the individual parts of the SMPL Mech Mod and then move onto showing how to use it.

     

    What is the SMPL Mech Mod?

    Created as a stripped down, easy to use Mech Mod, the SMPL Mech Mod is a fully analog mod with no adjustable parts and no caps.

    smpl-mechanical-mod-4

    • Threading Connection – Found at the top of the SMPL Mech Mod, it’s got nothing other than a small hole with 510 threading for your atomizer. The atomizer will make a direct connection to the battery that is within the SMPL.
    • Battery Tube – The main body of the SMPL, this will be the tube that holds your battery.
    • Firing Button – The SMPL has it’s own unique firing button, in that it is not a button at all. Instead, it’s a threaded ‘cap’ that has an indent in the center that is used to lock the button down or unlock it.

    How to Use the SMPL Mech Mod

    • Insert the Battery

    Using a coin, or some other small item, twist the firing button counter-clockwise until it is unlocked from the SMPL. Once open, insert your 18650 battery into the SMPL with the positive side leading the way. Re-attach the firing button, but not all the way. Since there’s no ‘formal’ firing button, once it’s pushed in all the way it’ll immediately start sending out voltage.

    • Attach the Atomizer

    Grab your 510 threaded atomizer and line it up with the threading connection at the top of the SMPL. Then, twist the atomizer clockwise until it’s firmly attached to the SMPL.

    • Start Vaping

    Now you can twist the firing button until it’s all the way in. The vaporizing process should begin, and everything should come easily from here. Just like the name says, it should all be very simple.

     

    Thanks for Reading our Guide on how to Use the SMPL Mech Mod!

    We hope we’ve cleared things up for you, and that you’ve got everything running smoothly.

    Buy it Here: SMPL Mech Mod

    Happy Vaping!

  • Guide: How To Use The AR Desert Camo Mech Mod

    Welcome to the Vapor Puffs guide on how to use the AR Desert Camo Mech Mod. This guide will start by giving a bit of a run down on the parts of the AR Desert Camo Mech Mod before going into a step by step guide on how to make it work.

    What Is The AR Desert Camo Mech Mod?

    The AR Desert Camo Mech Mod is an analog mod covered from top to bottom in vent holes. They’re made for use with 18650 batteries.

    desert-camo-mod-1

    • Threading Connection-Top Cap – Found at the top end, this side has a 510 threaded hole on the outside. When removed, it reveals a Silver and Copper plated surface that will make contact with the battery.
    • Battery Tube – This is the main part of the AR Desert Camo, and it’s where your batteries will go into. It’s covered in vent holes, 20 total.
    • Firing Button-Bottom Cap – On the bottom end is the firing button that will make the second silver and copper plated contact connect to the battery when pushed.

    How To Use The AR Desert Camo Mech Mod

    • Remove the Bottom Cap

    First, we’re going to have to insert the battery into the AR Desert Camo Mech Mod. In order to do that, remove the bottom cap from the battery tube. Now, insert your batteries into the battery tube with the positive end towards the top cap. Afterwards, re-attach the bottom cap to the battery tube.

    • Attach the Atomizer

    Now grab your 510 threaded Atomizer and attach it to the 510 threading connection on the top cap by lining it up with the threading hole and then twisting it clockwise until it’s attached.

    • Begin Vaping

    Once everything is good to go, hit the firing button on the bottom of the AR Desert Camo Mech Mod and hold it down. You should notice your atomizer begin to work, and from here on everything should come naturally.

    Thanks For Reading Our Guide On How To Use The AR Desert Camo Mech Mod!

    We hope we’ve helped you get it working.

    Buy It Here: AR Desert Camo Mech Mod

    Happy Vaping!

     

  • how to use the aerotank turbo Guide: How To Use The Aerotank Turbo

    Welcome to Vapor Puffs guide on how to use the Aerotank Turbo by Kanger. The guide will start by looking at the individual parts that make up the Aerotank Turbo, and then give you a step by step guide on how to use it.

    What Is The Aerotank Turbo?

    The Aerotank Turbo is one of the latest upgrades to Kanger’s Aerotank atomizers. The Aerotank Turbo’s biggest and most noticeable change is the huge 6.0 ml capacity, which adds a lot of girth to the atomizer.

    how to use the aerotank turbo

    • Mouthpiece – This is where your mouth goes. It’s replaceable.
    • Mouthpiece Ring – This ring is what the mouthpiece connects to. It can be removed and replaced if necessary.
    • eLiquid Tank – This is where the eLiquid is stored. It’s the biggest part of the atomizer.
    • Coil Unit – The Aerotank Turbo uses two coil units that are hidden within the eLiquid Tank.
    • Connection Ring – This is the ring that has the Kangertech writing and Arrows on it. Twisting this ring clockwise loosens the connection to the eLiquid Tank, allowing you to access the Coil Units.
    • Airflow Ring – This Ring turns only turns a short amount. By turning it clockwise you open up more airflow slots.
    • Threading Connection – This is the small threaded part on the back end of the Aerotank Turbo. It’ll be the part that connects to your battery.

    How To Use The Aerotank Turbo

    • Fill the eLiquid Tank

    Turn the Connection Ring clockwise until the eLiquid Tank detaches from the base. Flip over the eLiquid Tank and you’ll see two empty tube (these lead to the mouthpiece, and will be filled by the Coil Units). Drip your eLiquid against the sides of the tank until it’s just below those two tubes, then reattach the base by lining up the Coil Units to the tubes, and twisting the ring counter-clockwise.

    • Adjust the Airflow Ring

    Set the airflow to whatever preference you prefer by twisting the Airflow Ring until you are at the amount of air holes you want uncovered. This can be adjusted at any time.

    • Attach to Battery

    Line up the Threading Connection to your battery and twist clockwise until it’s firmly attached. Then turn on your battery, and begin the vaping process. Everything should come naturally from here.

    • Replace the Coil Units

    After some amount of uses, you might notice the quality of your vaping starting to lessen. When that happens, it’s time to replace the Coil Units.

    Remove the eLiquid Tank from the base by turning the Connection Ring clockwise. Once it’s detached, you’ll notice two very thin tubes sticking up from the base. Turn each one counter-clockwise until they are detached. Then, attach the new ones by lining up the threading and twisting clockwise. Now, reattach the eLiquid Tank, and you’re all done.

    Thanks For Reading Our Guide On How To Use The Aerotank Turbo!

    We hope we’ve helped you figure out how to get it working.

    Buy It Here: Aerotank Turbo

    Happy Vaping!

  • Guide: How To Use The Aerotank Mega

    Welcome to the Vapor Puffs guide on how to use the Aerotank Mega atomizer. We’ll start the guide off with a brief introduction to the Aerotank Mega and it’s parts, and then move onto the guide showing you how to use it.

    What Is The Aerotank Mega?

    Made as an upgrade to Kanger’s original Aerotank, the Aerotank Mega is an adjustable airflow atomizer that is seen as easier to use than it’s predecessors. Let’s take a look at the parts.

    kanger-aerotank-mega-5

    • Mouthpiece – This is where your mouth will go. It can be removed by twisting and pulling from the top, in order to be replaced with another or cleaned.
    • eLiquid Tank – This glass part is where your eLiquid will be held. It can be replaced with the stainless steel tank that comes in the box (and is pictured above).
    • Coil Unit – Hidden within the tank is the Coil Unit. It can be accessed by removing the Threading Connection and replaced with other compatible Coil Units. It contains the wicks and heating element that will vaporize the eLiquid.
    • Airflow Ring – A ring with small dents all around it and one specific hole, this can be turned in order to adjust the amount of air that goes through the atomizer.
    • Threading Connection – The Threading Connection is the small part sticking out from the bottom of the Aerotank Mega. It’s a 510 threading that will be used to connect to a battery.

    How To Use The Aerotank Mega

    • Fill the Tank

    Grab the atomizer right on the ring between the Threading Connection and Airflow ring and twist counter-clockwise in order to open the tank and reveal the Coil Unit. When dripping the eLiquid into the tank, make sure not to drip into the center hole as it leads to the mouthpiece. Instead, drip into the four smaller holes that are closer to the walls of the tank.

    Once you’ve finished filling the tank, reattach the base by lining up the Coil Unit with the center tube and twist counter-clockwise.

    • Set the Airflow

    By twisting the Airflow Ring you can change the amount of air that flows through the atomizer. You can do this at any time while using the Aerotank Mega and you can see how much air you’re allowing into it by peeking into the small hole on the ring. While twisting it, you should notice the airflow trench that is behind the ring expand as you twist it clockwise, meaning more air will go through the atomizer.

    The Airflow setting is entirely based on personal preference.

    • Attach to Battery

    Line up the 510 Threading Connection to a battery that also uses 510 threading. Once connected, turn on the battery and begin vaping. Everything should come easily from here.

    • Change the Coil Unit

    This doesn’t have to be done after every use, but eventually you will notice that the Atomizer might not be giving off a taste as strong as before or just might not be heating up enough. When it reaches that point, it’s time to change the coil.

    Remove the base of the Aerotank Mega the same way you did before in order to pour in eLiquid. Now, grab onto the small tube that is the coil unit and twist counter-clockwise. It should easily come off. The Aerotank Mega comes with an extra Coil Unit in the box, so take that Coil Unit and place it in the old unit’s spot by twisting it counter-clockwise against the base. Once it’s firmly attached, you’re good to go.

    Thanks For Reading Our Guide On How To Use The Aerotank Mega!

    We hope we’ve helped you get it all figured out.

    Buy It Here: Aerotank Mega

    Happy Vaping!